Ceramic pcb manufacturer right now: When the board has only copper tracks and features, and no circuit elements such as capacitors, resistors or active devices have been manufactured into the actual substrate of the board, it is more correctly referred to as printed wiring board (PWB) or etched wiring board. Use of the term PWB or printed wiring board although more accurate and distinct from what would be known as a true printed circuit board, has generally fallen by the wayside for many people as the distinction between circuit and wiring has become blurred. Find additional info at pcb assembly manufacturer.
Metal Core PCB means the core (base) material for PCB is the metal, not the normal FR4/CEM1-3, etc. and currently the most common metal used for MCPCB manufacturer are Aluminum, Copper and steel alloy. Aluminum has good heat transferring and dissipation ability, but yet relatively cheaper; copper has even better performance but relatively more expensive, and steel can be divided into normal steel and stainless steel. It more rigid than both aluminum and copper, but thermal conductivity is lower than them too. People will choose their own base/core material according to their different application.
What is Ultra-Thin HDI PCB? High-Density Interconnect PCB is simply an ultra-thin PCB having more counts of interconnections, covering minimal space, leading to circuit board miniaturization. The components of HDI PCB are positioned closer, reducing the board space significantly but not compromising its performance. HDI is among the fastest advancing PCB technologies, capable of integrating smaller capture pads and vias and higher densities of connection pad. HDI PCBs have buried and blind vias and usually comprise of microvias with diameter of 0.006 or lower. Extra thin HDI PCBs provide better construction, layout and design choices by integrating outstanding features like microvias.
Double-layer printed circuit boards (PCBs) consist of two layers of conductive material, typically copper, separated by an insulating layer. The top and bottom layers are etched to form the desired circuitry. Double-layer PCBs offer several advantages over single-layer PCBs, including increased routing options and the ability to place components on both sides of the board. However, they are also more expensive and require more careful design to avoid short circuits.
Best Technology, establish on June 28, 2006, is a Hong Kong registered company whom focused on one-stop solution provider of FPC, Rigid-flex, MCPCB, FR4 PCB, Ceramic PCB, Special PCB such as Heavy Copper (up to 20 OZ), extra thin PCB (0.10, 0.15mm), and PCB assembly service.
According to different manufacturing method, current there’re three basic types for ceramic board: A) Thick Film Ceramic Board Thick Film Ceramic PCB: Using this technology, the thickness of conductor layer exceeds 10 micron, more thick than spurting technology. The conductor is silver or gold palladium, and was printed on ceramic substrate. More for Thick Film Ceramic PCB. B) DCB Ceramic Board DCB (Direct Copper Bonded) technology denotes a special process in which the copper foil and the core (Al2O3 or ALN), on one or both sides, are directly bonded under appropriate high temperature and pressure. See additional information at bstpcb.com.
A single sided flexible printed circuit (1 layer flex circuit) is a flex circuit with one layer of copper trace on one substrate, and with one layer Polyimide coverlay laminated to copper trace so that only one side copper will be exposed, so that it only allowing access to copper trace from one side, comparing to dual access flex circuit which allows access from both top and bottom side of flex circuit. As there’s only one layer of copper trace, so it also named as 1 layer flexible printed circuit, or 1 layer flexible circuit, or even 1 layer FPC, or 1L FPC. The multi layer flex circuit refer to a flex circuit with more than 2 layer circuit layers. Three or more flexible conductive layers with flexible insulating layers between each one, which are interconnected by way of metallized hole through the vias/holes and plating to form a conductive path between the different layers, and external are polyimide insulating layers. Quality Policy: PCB Quality is the core of products. All of engineer & vital department guys has more than five years expenrience in PCB industry, we follow up the default PCB standard, as well as with clients’ special request.
The white silkscreen layer is applied on top of the soldermask layer. The silkscreen adds letters, numbers, and symbols to the PCB that allow for easier assembly and indicators for humans to better understand the board. We often use silkscreen labels to indicate what the function of each pin or LED. Silkscreen is most commonly white but any ink color can be used. Black, gray, red, and even yellow silkscreen colors are widely available; it is, however, uncommon to see more than one color on a single board.
Heavy Copper Board does not have a set of definition per IPC. According to PCB industry, however, peopel generally use this name to identify a printed circuit board with copper conductors 3 oz/ft2 – 10 oz/ft2 in inner and/or outer layers. And Extreme heavy copper PCB refers to 20 oz/ft2 to 200 oz/ft2 printed circuit board. Heavy copper normally used for a various products but not limited to: high power distribution, heat dissipation, planar transformers, power convertors, and so on.